How To Repair Cut Coaxial Cable

Download Article

Download Article

Coaxial cable, unremarkably referred to equally coax, is an electronic signal wire used for signals that are noise sensitive. To protect the signal of interest, coax wraps a unmarried conductor with a tube of metal foil and mesh. The tube runs co-axially over the signal conductor and requires a specific coax crimp termination method. Use these tips to learn how to splice coax cablevision.

Steps

1. ane

   Create termination points.

   • Cutting off the ends of the coax cables to be spliced. Use small sharp wire cutters. Create squared off surfaces, rather than beveled surfaces.
   • Mold the ends of the coax using your fingers. Mold the ends of the cables back into cylinders. They will have been distorted by the pressure of the cut performance.

2. 2

   Insert the cables, one at a time, into a coax stripper tool. Coax stripper tools are available at hardware and electrical stores. Equally each cablevision is inserted, make certain that the end of the cable is seated flush against the wall or guide on the stripping tool. This ensures proper strip lengths.

   Advertisement

3. 3

   Clamp the stripping tool around each cable. Once the tool is in place around the cable, smoothly spin the tool around the cable four or 5 times. Go on the rotation in ane place on each cable. Do non apply any forcefulness that would pull on the cablevision insulation coating.

4. four

   Remove the coax stripping tool from each cablevision every bit the strip cut is completed. The stripping tool made two cuts simultaneously. Use your fingers to gently pull off the material nearest the terminate of each cablevision. This exposes the blank centre usher of each cablevision.

5. v

   Pull off the outer insulation that has been freed on each cable past the 2nd cut made by the stripping tool. Pull gently with your fingers. This exposes a layer of foil on each cable.

6. 6

   Tear off the exposed foil on each cable. This volition betrayal a layer of metallic mesh on each cable.

7. vii

   Bend back the exposed metal mesh on each cable with your fingers. Exercise not tear the layer of foil that is under the metal mesh. The layer of foil protects the inner insulation. Bend the mesh all the fashion back so that information technology is molded over the end of the outer insulation on each cablevision.

8. eight

   Press the end of each cable into the back of an F connector. Make sure that on each connector, the white inner insulation tin be seen pressing against the front flange of the connector. It may exist necessary to jiggle and continue to push button the coax and the connector together to achieve proper seating. Use straight pressure level simply. Exercise not twist the coax in the torso of the connector.

9. ix

   Crimp the connections. Place each F connector into a coax crimping tool, which is available at hardware and electrical stores. Execute the crimp by fully squeezing the crimping tool handle. Release the handle and open the crimping tool. Remove the finished crimp connection from the tool.

10. 10

    Consummate the splice. Connect the two cables to either finish of a BNC female to female coaxial adapter. These are bachelor at hardware and electrical stores.

Advert

Add New Question

• Question

  How can I make up one's mind if the comcast cables are spliced or connected to my neighbor's homes? My cable reception and internet are continually dropped.

  

  Use an O-scope to transport a pulse into the cable and look for spikes and/or discontinuities reflected. In that location should only be ane at the distance the coaxial runs to the drop box cablevision origin.

• Question

  Tin I plug a True cat 6 ethernet cablevision into my neighbor'southward router?

  

  Bold that the device you want to connect is within 100 thou of the router (accounting for windows, wall, fences, etc.), and so you should be able to connect to the router.

• Question

  Can I splice two cables together similar a regular wire splice? Or can I solder 2 cables together?

  

  No. There are certain physical effects that come into play at high frequencies which are not significant at low frequencies or DC - to simplify greatly, the space around the cable is itself electronically agile, non merely the metal part itself. That'southward why you demand coaxial cable, non just two wires side-past-side like regular mains ability cable. This also ways that you tin't reliably splice coaxial cable without very careful consideration of the joint geometry.

• Question

  Practise F connectors come up in different sizes for dissimilar cables (RG6, RG59, etc)?

  

  Yes. You lot have to lucifer the size and fashion of the connector to the correct wire. Also, avoid crimp-on fittings. Only utilize compression fittings.

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

Video

Thanks for submitting a tip for review!

Things You'll Need

• Wire cutters
• Coax cablevision stripping tool
• F connector
• F connector compression tool
• BNC coaxial adapter

Almost This Commodity

Thanks to all authors for creating a page that has been read 295,205 times.

Is this article upwardly to engagement?

Source: https://www.wikihow.com/Splice-Coax-Cable

Share this post